Average Reviews:
(More customer reviews)I purchased the version with the 12-inch antenna to use in my home office, and got it a couple days ago. The package says it installs in a minute, and that's basically true. It took me 15 minutes because I read the instructions and had to think about where to put it, but if I did it again, I could probably actually take the items out of the package and get it in place and operating in a minute.
It works very well. My provider is AT&T, which I'm stuck with because I have an iPhone. My wife gets a great Verizon signal, but my AT&T signal ranged from no service to two bars at any given time at any place in my house. A few seconds after installing the Wilson device that changed, and now I get from 2 bars to 5 bars within my home office.
I looked at another device that claims to provide a whole-house improved signal, and perhaps it does. The problem for me is that installation seemed complicated due to the need for very wide separation between the antenna that receives the outside cell signal and the amplifier that retransmits the stronger signal, which included getting wiring through wall or ceilings etc. In the case of the Wilson device, all you need do is keep the two apart by 8 feet or so, which was better for me.
I'm not a techy but it seems that the tradeoff is that the separation requirements are lower with this Wilson device, but the rebroadcasted signal is less powerful, so the signal improvement range is not whole-house, but more room sized. Fortunately, that works fine for me.
I have three windows together set up like a bay window of sorts. I used the suction cups to mount the antenna in the upper right of that set of windows. I then ran the antenaa wire over the top of the windows to the amplifier hanging on the left. I didn't even affix the amplifier to the wall, it just hangs from the antenna cord. It's behind the curtain so it's not seen.
I placed the antenna, reached up and ran the wire over the sill, connected the amplifier to the end of the wire and plugged it in. A second later the light went green, meaning that the separation distance is OK, and my phone went from 1 bar to 4. Easy.
The packaging seems to emphasize use in cars and trucks, so I'm guessing that this is mostly used by truckers and commuters who drive through a lot of weak signal areas. But it also gives directions for installing in a home or office, which is what I did, and I can report that it works well for that purpose, at least in my situation.
Click Here to see more reviews about: Wilson Electronics 801241 MobilePro Multiple-User Cell Phone Signal Booster for Car/Home
If you experience dropped calls and poor cell phone signal quality in your car, home, or office, then the Wilson MobilePro Cell Phone Signal Booster Kit is the solution. Increasing your cell phone's power by more than 12 times, the Wilson MobilePro significantly improves the performance of your cellular and data devices by increasing the power output of your cell phone signal where you are experiencing a weak signal. Designed for portability and mobility, the MobilePro includes several power adapters, and is easily moved from your vehicle to your home, hotel, airport, or office, creating an improved cellular signal.
Setting up the MobilePro takes just minutes. View larger.It's All About PowerThe primary cause of dropped calls is low signal output power from the cell phone to the cell tower, which limits the phone's ability to communicate with the tower. A typical cell phone provides merely one-fifth of a watt of output power. To address this problem, the amplifier and the included magnet mount antenna work together to increase the phone's output power by more than 12 times over using just the phone alone.
Enjoy Premium Reception and Fewer Dropped CallsLiving or working in an area with limited cell phone coverage, which is caused by natural and man-made obstructions or by living out of range from a cell phone tower, you know how frustrating weak reception can be. By increasing the power output of your cell phone signal, the Wilson MobilePro helps eliminate most of the signal loss caused by these obstructions. It's important to note that the strongest signal is obtained when the MobilePro is within two feet of your cell phone, laptop, or data card. If you sit at a distance greater than two feet, simply set your phone next to the MobilePro booster and use a Bluetooth headset.
The MobilePro comes with several power options, including a vehicle cigarette lighter adapter, a USB power cable, and a standard five-volt AC/DC adapter. The variety of power options ensures that you'll have a boosted signal whether you're driving in your car, traveling with your laptop, or working at your desk. Included with the booster kit is a convenient carrying case that fits neatly inside a briefcase, handbag, or suitcase.
Once installed, the MobilePro can simultaneously support multiple cell phones and data cards. You'll experience fewer dropped calls, clearer call quality, and improved data rates--even with 3G technologies.
Installing the MobileProInstallation is quick and easy; everything you need for installation in a building or car is included in the kit.
In a BuildingTo install, simply attach the suction-cup window bracket to the inside of the window and place the magnet mount antenna on the bracket. Connect the magnet mount antenna to the amplifier. Power the amplifier by using the included USB power cord and plugging it into a computer's USB port, or by using the standard AC adapter. Place the MobilePro within 12 inches of your phone, laptop, or data card to receive an improved signal.
In a CarTo install, simply attach the magnet mount antenna to the roof of your vehicle. Connect the cable of the magnet mount antenna to the amplifier. Mount the amplifier to the dash or other area using the supplied mounting hardware. Power the amplifier using the cigarette lighter adapter, or by plugging the USB cord into your laptop computer. Now you're ready to enjoy a stronger cell phone signal typically within two feet of the amplifier.
Compatible with Most Cell Phone Models and ProvidersThe Wilson MobilePro is compatible with all US and Canadian cellular providers, excluding iDEN, Nextel, and MIKE. The kit supports CDMA, TDMA, GSM, and AMPS cell phone technologies, as well as data protocols such as GPRS, 1xRTT, HSDPA, EVDO, and EDGE.
The use of radio distribution equipment that enhances, extends or amplifies a wireless signal may be prohibited without the consent of the wireless carrier upon whose network such equipment will be used. You should consult with your carrier before purchasing such equipment to use with that carrier's service.
Specifications
Frequency: 824-894 MHz / 1850-1990 MHz
Gain: 40dB / 42dB
Max Output Power: 500 mw
Max RF (downlink): +8dBm
Noise Figure: 3.5dB nominal
Flatness: ±4dB
Isolation: > 90dB
Power Requirements: 5V - 8V
Connectors: SMA Female
Dimensions: 2 x 4.75 x 1 inches
Weight: 3 oz
What's in the BoxMobilePro unit, 12-inch magnet-mount antenna, USB power cable, cigarette-lighter power adapter, five-volt AC/DC adapter, two convenient mounting options, and carrying case.
Get 43% OFF
No comments:
Post a Comment